Large gear

This large gear turns the small one to rotate the cylinder .

这个大齿轮带动小齿轮使滚筒旋转。

This large gear turns the small one .

这个大齿轮带动那个小齿轮。

Important Development of Dynamic Measuring Technology of Large Gear Transmission System

大型齿轮传动系统动态测量技术的重要发展

The Principle and Technology for On-line Tooth Measurement for Large Gear

大齿轮齿形在机测量原理与技术

New Method for Large Gear form On-line Measurement

大齿轮在位测量中齿形误差分析的新方法

Study of In-suit Integrated Measuring Theory and Technology for Large Gear

大型齿轮在位综合测量原理与技术的研究

Distortion Control of Large Gear Shaft During Heat Treatment

大齿轮轴热处理畸变的控制

A new method for cutting the profile of tooth of large gear ring

一种大型齿圈齿形加工的新方法

Technology of on line measuring large gear alignment errors

大齿轮齿向误差在机测量技术

Study on Precision Angle - Measuring Equipment in Large Gear On-machine Measuring

大型齿轮在机测量中精密测角装置的研究

Study of Run in About Large Gear Reducer of Cement ball Mill

球磨机大型齿轮减速机的跑合试验研究

Installation experience of large gear casing by using epoxy resin mortar

用环氧砂浆配作大型减速机底座垫板施工的经验

Fault Diagnosis about Turning Bearing of Large Gear Box

高炉布料器齿轮箱回转支承故障诊断

Large Gear Inside the Gear End of the Transformation Hardening Machine CNC

大型齿轮内齿圈端面淬火机床的数控化改造

A Study on the Deformation in Large Gear Ring Machining and Its Preventive Measures

大型齿圈加工变形与防治措施的研究

Finite Element Analysis of Contact Unit of Large Gear Ratio Traction Drive Speed - increasing Mechanism

大传动比牵引驱动增速刀柄接触部件有限元分析

On-line measuring a tooth profile of a large gear has a good prospect .

在机测量大齿轮齿形误差具有广阔的发展前景。

Measurement Error Separate and Simulation Studies for Large Gear Based on Rack-shaped-edge Probe

基于刃边齿条形测头的大型齿轮在位测量的误差分离和仿真研究

The Application of Programmable Dynamic Frequency Doubler on Large Gear Testing in Situ

可编程动态倍频器在大齿轮在机测量中的应用

Development and Research and Finite Element Analysis of the Large Gear Ratio Traction Drive Speed-Increasing Mechanism

大传动比牵引驱动增速系统的开发研制及其有限元分析

This new method is especially suitable for developing on-line measuring instruments for large gear 's profile .

这种新方法特别适用于大齿轮齿形误差在位检测仪器的研制和开发。

Fault Diagnosis of the Cross-rolling Bearing in Large Gear Box

大型齿轮箱回转支承故障诊断

Sometimes , many spur gears are used at once to create very large gear reductions .

有时，一次用多级齿轮传动可获得大的降速比。

Repair to Broken Teeth of Reducer Large Gear Used in WK-4 Excavator

WKz&4型挖掘机中减速机大齿轮断齿的修复

Simulation analysis on theory of on - line measuring a tooth Profile of a large gear base on rack - edge probe

基于齿条测头的大齿轮齿形在机测量原理仿真分析

General principle and ERROR-VARIATION analysis of on-machine measuring large gear profile error with rack-head

齿条刃边测头在位测量大型齿轮齿形误差的基本原理及误差与变异分析

Radiation source and detector was fixed on a ring connected with the kickstand by large gear .

装置将辐射源装置和探测器固定在一环形支架上，该环形支架由轴承与支座连接，通过伺服电机驱动可以环绕被检客体旋转；

Design of a Hob with Short and Straight Edges for Machining the Hardened Work-Surfaces of a Large Gear

大型齿轮的短直刃硬齿面滚刀设计

Procedure for welding broken teeth of large gear is presented in this article , The procedure developed is easy , simple , low cost and with better result .

介绍了大齿轮断齿的补焊修复新工艺，该工艺简便易行，耗费低廉，效果良好。

Based on analysis and comparison of domestic and foreign measuring principle and technology of large gear , in-suit measurement is ascertained as the research direction of this thesis .

在分析比较国内外大型齿轮测量原理与技术的基础上，确定了以在位测量，作为本论文的研究方向。